News Center

——  NEWS CENTER  ——

News Center
Contact Us

Xi'an Shenghongchuang Instrument Co., Ltd.

Contact: Mr. Zhang

Mobile: 15529283736
Email: shc-sensor@qq.com

Address: Fortune Building, Sanqiao Street, Xixian New Area, Xi'an, Shaanxi Province

How to Select a Compact Differential Pressure Sensor When Installation Space Is Limited
Added to Favorites:125

How to Select a Compact Differential Pressure Sensor When Installation Space Is Limited

In compact equipment, air duct enclosures, small filtration units, laboratory instruments, clean control units, and automated equipment, the space available for differential pressure measurement is often very limited. When selecting a compact differential pressure sensor in such cases, the decision should not be based solely on whether the product housing is “small enough.” It is also necessary to verify the installation clearance, pressure port orientation, cable bending radius, measuring range, allowable overload, and on-site electromagnetic environment.

A differential pressure sensor measures the pressure difference between the high-pressure side and the low-pressure side. It can be used for filter blockage monitoring, indirect airflow calculation, liquid level difference measurement, pressure balancing in sealed containers, and gas circuit status assessment. The more compact the space, the more difficult subsequent maintenance, installation, and removal become. Therefore, preliminary technical evaluation should give equal priority to mechanical compatibility and measurement reliability.

Leveraging the manufacturing and R&D capabilities of Shaanxi Qinkong Sensor Technology Co., Ltd., Xi'an Shenghongchuang Instrumentation Co., Ltd. can provide differential pressure sensors, differential pressure transmitters, and related measurement and control products for conventional industrial sites and equipment integration requirements, and can carry out non-standard adaptation based on interfaces, outputs, ranges, and installation methods. For equipment manufacturers, clarifying boundary conditions as early as possible can reduce the costs of rework and on-site piping modifications.

In practical selection, the sequence of “measure the space first, then determine the range, check the interfaces afterward, and finally confirm the environment” can be followed. This can prevent the product from failing to fit while also reducing measurement deviations and operational failures caused by an excessively large range, incompatible interfaces, or incompatible media.

I. Convert Installation Space into Verifiable Data First

Measure More Than Length, Width, and Height; Reserve Space for Wiring and Maintenance

Technical personnel should record the effective length, width, and height of the installation chamber rather than only checking the dimensions of the equipment enclosure. In addition to the sensor body, fittings, elbows, plugs, cable outlets, and mounting brackets must also be included. If the wiring terminal is located on the side or bottom, additional space required for cable bending should be considered.

For example, the clear depth of an installation slot may be 80 mm and the sensor body depth may be 52 mm, making it appear that the sensor can fit. However, if the interface piping occupies 15 mm and the cable requires another 20 mm for minimum bending and plug-in/removal operations, reliable installation is no longer feasible. In compact spaces, side cable outlets, short fittings, or integrated plug-in structures are generally more effective than simply reducing the housing size.

Installation orientation also affects the final dimensions. Some products have high- and low-pressure ports on the front and are suitable for flat-surface installation; others have ports on the side and are better suited for installation close to air ducts or piping. If there are access doors, heat sinks, moving components, or cable routing channels inside the equipment, a basic operating clearance of at least 10 mm to 20 mm should also be reserved.

For mass-produced equipment, it is recommended to indicate the sensor outline, interface orientation, wiring harness path, and screw removal direction in 3D drawings at the same time. Do not confirm the location solely by 2D projection, otherwise issues such as plug interference, hose bending, or inability to tighten fasteners may easily occur during the prototype stage.

Verification ItemRecommended Confirmation ItemsCommon Risks
Main installation dimensionsLength, width, height, and mounting hole spacingThe housing fits, but the screws cannot be installed
Port clearancePort orientation, tubing length, and hose bend radiusHose kinking, unstable pressure tapping, or leakage
Wiring spaceConnector height, cable outlet, and maintenance clearanceThe connector cannot be plugged or unplugged, and the cable is under tension
Environmental locationHeat sources, vibration sources, variable frequency drives, and humid areasZero drift, signal fluctuations, or reduced service life

II. Range and Accuracy Should Be Determined Around the Actual Differential Pressure Range

A Smaller Range Does Not Necessarily Mean It Is More Suitable

The differential pressure range should cover normal operating values, startup fluctuations, and abnormal short-term peaks. For example, in filter differential pressure monitoring, if the initial differential pressure is approximately 100 Pa, the replacement reminder point is 500 Pa, and a short-term fluctuation of 800 Pa may occur during system startup, it is not advisable to select only a 500 Pa full-scale sensor. A 0 Pa to 1000 Pa range or a specification closer to the on-site upper limit may be considered.

When the range is too large, the actual operating point accounts for too small a proportion of the full scale, which affects resolution. When the range is too small, impact differential pressure may cause overrange conditions or even damage the sensing element. In engineering applications, the commonly used differential pressure can be controlled within 30% to 80% of the full-scale range and then confirmed in combination with the allowable overload capacity.

The accuracy reference must be clearly understood. The common specification “±0.5%FS” refers to an error relative to full scale rather than the current reading. If a 0 kPa to 10 kPa product is selected, its ±0.5%FS corresponds to an error of approximately ±50 Pa. When the actual measured value is only 200 Pa, this error may significantly affect the assessment. Therefore, the range should not be increased blindly in low differential pressure applications.

It is also necessary to distinguish between the differential pressure range and static pressure conditions. In some applications, the pressure difference between the two sides is small, but the absolute pipeline pressure is high, such as in sealed gas transmission or high-pressure equipment bypasses. Under such conditions, the allowable static pressure at both sides of the sensor and the single-side overpressure value must be confirmed simultaneously; attention should not be given only to the differential pressure value.

Reference for Range Selection in Common Operating Conditions

Application ScenarioCommon Differential Pressure RangesSelection Considerations
Cleanroom and air duct monitoring10 Pa to 1000 PaLow-range accuracy, zero-point stability, and installation position
Filter differential pressure alarm100 Pa to 5 kPaBlockage limit, short-term surges, and media cleanliness
Equipment pneumatic circuit status monitoring1 kPa to 50 kPaResponse speed, overload capacity, and output compatibility
Liquid level or differential pressure in sealed vessels5 kPa to 100 kPaStatic pressure, media corrosiveness, and sealing materials

III. Interfaces, Media, and Installation Methods Determine Long-Term Stability

Prioritize Simple, Short, and Reliable Pressure Connections

Common connection methods for compact differential pressure sensors include barbed fittings, threaded interfaces, push-to-connect interfaces, and customized fittings. For air, non-corrosive gases, and low-pressure air ducts, hose connections are flexible and suitable for narrow areas inside equipment. For liquids, pressurized media, or applications with high vibration, the sealing reliability and pressure rating of threaded connections should be given particular consideration.

The high-pressure side and low-pressure side must be connected according to the markings. For gas circuits where positive and negative pressure may switch repeatedly, it should be confirmed whether the sensor supports bidirectional differential pressure measurement, or a model with the corresponding range and protection capability should be selected. Reversed interface connections may not necessarily damage the product, but they will reverse the output direction and may lead to incorrect control logic judgments.

Media compatibility must not be overlooked. Ordinary dry air, oil-containing compressed air, humid air, corrosive gases, and condensate environments have different requirements for the sensing element, sealing rings, and housing materials. If moisture may be generated in the gas circuit, condensate should be prevented from entering the pressure ports directly, and liquid accumulation locations, impulse line routing, and necessary isolation measures should be considered in the design.

During installation, excessively long, overly narrow, or severely bent impulse lines should be minimized. The more complex the pressure transmission path, the more apparent the response lag and pressure-loss error. For control systems that need to quickly identify fan start-stop conditions and valve actions, the length and diameter of pressure tubing, as well as the consistency of the paths on both sides, should be included in the design review.

IV. Output Signals and Anti-Interference Capability Must Match the Control System

Determine the Sensor Configuration Based on the Controller Input Type

In space-constrained equipment, sensors are usually connected directly to PLCs, control boards, display instruments, or variable-frequency control units. Before selection, the input types supported by the control end should be clarified, such as 4 mA to 20 mA, 0 V to 10 V, 0 V to 5 V, RS485 communication, or switching output. Output mismatches increase the need for signal conversion modules, occupy additional space, and add wiring complexity.

4 mA to 20 mA is suitable for industrial sites with long cables and strong interference and provides good anti-interference performance. Voltage outputs are easy to wire and suitable for short-distance connections inside equipment. RS485 can transmit more parameters and status information and is suitable for multi-point networking and intelligent instrument systems. For applications with cable lengths exceeding 10 m or with variable-frequency drives or high-power motors nearby, shielded cables, grounding methods, and signal isolation requirements should be evaluated as a priority.

Power supply conditions should also be determined in advance. A common industrial power supply is 24 VDC, but different products may have requirements for the allowable voltage range. Power fluctuations, reversed polarity, common-ground interference, and surge impacts can all affect sensor output stability. When routing cables in compact equipment, the sensor signal cable should be laid separately from power cables as far as possible, with a spacing of more than 50 mm reserved according to the site layout.

In addition to conventional accuracy, zero drift, temperature effects, response time, and long-term stability also deserve attention. For low differential pressure detection, output stability when the ambient temperature changes from 0℃ to 50℃ often reflects actual performance more effectively than a single laboratory accuracy parameter.

V. Establish a Quick Selection Checklist to Shorten the Technical Communication Cycle

The More Complete the Submitted Parameters, the More Reliable the Matching Result

When purchasers or technical personnel consult suppliers about compact differential pressure sensors, it is recommended to provide the installation space drawing, medium name, normal and maximum differential pressure values, static pressure at both ends, temperature range, interface type, output signal, power supply, and quantity required in one submission. For non-standard equipment, it should also be stated whether brackets, displays, alarms, or special cable lengths are required.

If all parameters cannot be obtained temporarily, at least four basic items should first be determined: available installation dimensions, measurement medium, target differential pressure range, and controller input type. These four items can complete most of the initial screening, after which pressure resistance, accuracy, materials, and protection requirements can be refined and confirmed.

Xi'an Shenghongchuang Instrumentation Co., Ltd. can assist in verifying differential pressure ranges, installation structures, interface connections, and signal output solutions according to equipment integration, industrial automation retrofit, and special operating condition requirements. For projects with particularly compact spaces, it is recommended to first provide photos or dimensional drawings of the installation location so that technical personnel can assess sensor dimensions and wiring feasibility based on the actual layout.

The correct selection of a compact differential pressure sensor is essentially a comprehensive match among measurement requirements, mechanical structure, and electrical systems. When defining a project, existing installation dimensions, operating condition parameters, and control requirements can be compiled, and Xi'an Shenghongchuang Instrumentation Co., Ltd. can be contacted for targeted product selection and technical coordination recommendations.

Submit