News Center
—— NEWS CENTER ——
Xi'an Shenghongchuang Instrument Co., Ltd.
Contact: Mr. Zhang
Mobile: 15529283736
Email: shc-sensor@qq.com
Address: Fortune Building, Sanqiao Street, Xixian New Area, Xi'an, Shaanxi Province
Digital differential pressure sensors are used for applications such as air pressure monitoring, filter blockage detection, pipeline flow calculation, liquid level difference measurement, and cleanroom differential pressure control. The output protocol does not merely determine whether wiring is possible; it also affects signal interference resistance, measurement data integrity, commissioning efficiency, and the ease of future connection to host computers and IoT platforms.
During engineering selection, first confirm the existing input modules and communication interfaces of the control system. If the on-site PLC is equipped only with analog input modules, 4-20mA should be prioritized; if multiple devices need to be connected on one bus to read parameters and diagnostic status, RS485 is usually more suitable; if the project already uses industrial Ethernet, selection should be standardized according to the master station protocol.
For differential pressure measurement solutions provided by Xi'an Shenghongchuang Instrumentation Co., Ltd., it is recommended to confirm the measuring range, accuracy, power supply method, installation environment, and output protocol simultaneously. Protocol selection should serve actual control objectives and avoid unnecessary gateway, configuration, and maintenance costs solely for the sake of “digitalization.”
4-20mA is the most widely used output format for differential pressure sensors. 4mA usually corresponds to the lower limit of the measuring range, while 20mA corresponds to the upper limit. Devices such as PLCs, DCSs, digital displays, and variable frequency drives generally support this signal. Two-wire products can also complete power supply and signal transmission through the same loop, making wiring relatively simple.
In workshop environments with strong electromagnetic interference and long transmission distances, current signals are more stable than 0-10V voltage signals. In conventional industrial projects, 4-20mA transmission over several hundred meters generally provides good engineering reliability when shielded twisted-pair cables are used; the specific distance still needs to be calculated based on supply voltage, loop load, and cable impedance.
The 4mA “live zero” also facilitates fault identification. When loop current is significantly below the normal lower limit, the control system can identify an open circuit, power loss, or sensor abnormality. However, this method can generally transmit only one primary measured value and cannot simultaneously provide temperature compensation values, accumulated data, device parameters, or detailed diagnostic information.
RS485 is a physical communication interface commonly used in industrial instruments and is typically used with the Modbus RTU protocol in actual projects. One RS485 bus can connect multiple digital differential pressure sensors, and the master station can poll device addresses to read information such as differential pressure values, units, ranges, zero status, and alarm status, making it suitable for centralized monitoring systems.
Compared with each device separately occupying one analog channel, RS485 can save PLC expansion module and multicore cable costs. With standardized wiring, appropriate baud rates, and proper termination matching, a typical network can cover a communication distance of approximately 1200 meters. Common baud rates include 9600, 19200, and 38400bps; specific capacity must be determined based on cable, topology, and on-site interference conditions.
RS485 requires the host system to have communication capability. The project must define register addresses, data formats, byte order, device addresses, and communication parameters. Improper bus grounding, shield termination, or terminal resistor settings may also cause intermittent disconnections, so commissioning practices are more important than simple analog signal wiring.
Some high-end automation systems require interfaces such as CAN, HART, Profibus, Profinet, EtherNet/IP, or IO-Link. These solutions are suitable for projects where unified network standards have already been established, device asset management is required, or richer diagnostic data is needed. They should not be adopted blindly simply because the interface is “advanced.”
For example, HART can overlay digital communication on a 4-20mA analog signal, making it convenient to retain the original analog control loop while enabling remote parameter setting; IO-Link is more suitable for intelligent equipment and modular machinery; Profinet and EtherNet/IP are more common in production lines with higher requirements for real-time performance and system integration.
The more complex the protocol, the higher the requirements for master station modules, engineering software, network maintenance personnel, and spare parts management. For monitoring the differential pressure of a single air duct or providing a standard filter differential pressure alarm, complex industrial Ethernet protocols usually offer limited return on investment. System consistency and actual data requirements should be the basis for evaluation.
PLC projects should first inventory analog input channels, RS485 ports, communication expansion modules, and available address resources. If only 1 to 4 differential pressure sensors are connected and only real-time differential pressure values and high/low limit alarms are required, 4-20mA often provides lower engineering complexity and more intuitive program conversion relationships.
If more than 10 differential pressure sensors need to be connected in the same area, such as multiple air handling units, multiple groups of filter units, or multiple clean zones, using an RS485 bus can reduce I/O usage. In this case, communication timeout handling, data validity verification, and offline alarms should be designed in the PLC program. Numerical values alone should not be read while communication quality is ignored.
For applications requiring closed-loop control, such as adjusting a fan variable frequency drive based on air duct differential pressure, the refresh cycle must be carefully evaluated. 4-20mA can continuously reflect the process variable, whereas RS485 is affected by the polling cycle. For ventilation control requiring response at the second level, both are generally applicable, but excessive bus devices should not cause refresh delays.
In continuous production plants such as chemical, energy, and metallurgical facilities, DCS systems usually have clear instrument integration specifications. If the existing system is mainly based on 4-20mA, selecting the same type of output can reduce differences in configuration, acceptance, and subsequent maintenance; if the system has deployed a HART asset management platform, HART-compatible differential pressure transmitters may be considered.
In DCS applications, attention should not be limited to normal value transmission, but should also cover the identification of open circuits, over-range conditions, sensor failures, and communication abnormalities. It is recommended to configure high/low alarms, fault alarms, and interlock logic in layers to avoid mistaking sensor failures for sudden process differential pressure changes.
When hazardous areas, high-temperature media, or corrosive gases are involved, protocol selection must be considered together with explosion protection type, power isolation, and safety barrier configuration. Digital communication cannot replace intrinsically safe design; on-site electrical compliance and installation conditions are always the foundation for reliable differential pressure measurement operation.
Confirm the master station brand, model, and available interfaces, and avoid making decisions solely based on “RS485 supported.” Different devices may handle Modbus function codes, floating-point formats, and register addresses differently. Complete communication protocol documentation should be obtained before procurement.
Confirm the differential pressure range and output range. For example, when the range is 0-1000Pa, 4-20mA can correspond to 0-1000Pa; if actual operation remains below 100Pa for an extended period, a smaller-range model should be reevaluated, otherwise effective resolution and control accuracy will be affected.
Confirm power supply conditions and cable solutions. 24VDC is a common industrial site configuration, but loop voltage drop still needs to be calculated; RS485 should use shielded twisted-pair cable and, where possible, a daisy-chain bus topology to avoid arbitrary branches that cause reflections and unstable communication.
Areas concentrated with variable frequency drives, welding machines, high-power motors, and switching power supplies are prone to conducted and radiated interference. 4-20mA has good adaptability to common-mode interference, while RS485 also offers interference resistance through differential transmission, but its wiring requirements are more stringent.
Sensor signal cables should be routed separately from power cables whenever possible. Where crossing is necessary, they should cross at approximately 90 degrees and avoid long parallel runs; shield layers should generally be grounded at one end or according to the specified system grounding method, rather than being arbitrarily connected at multiple points, to prevent ground-loop interference.
For RS485 networks, terminal resistors are recommended at both ends of the line according to design requirements, and A/B wire definitions should be standardized in multi-device networks. Some manufacturers may use different terminal designations, such as A and B or D+ and D-. Product manuals and actual communication testing should prevail before wiring.
The common control range for cleanroom differential pressure is from several Pa to several tens of Pa, while air-conditioning filter differential pressure may gradually increase with operating cycles. In these applications, sensor range, zero stability, and pressure tapping installation methods often have a more direct impact on final control performance than the communication protocol itself.
If differential pressure only needs to be sent to a control cabinet for fan interlocking and over-limit alarms, a 4-20mA solution is simple and reliable. If multiple room differential pressures need to be managed simultaneously, trends recorded, alarm thresholds modified remotely, and a building management platform connected, RS485 offers greater overall advantages.
Pressure tapping tubes should avoid water accumulation, blockage, and leakage, and positive and negative pressure ports must not be connected in reverse. After sensor installation, zero-point checks and system commissioning should be performed; for low differential pressure measurement, even an installation error of only a few Pa may cause deviations in room differential pressure assessment.
When purchasing digital differential pressure sensors, it is recommended to specify the medium type, differential pressure range, static pressure range, accuracy class, process connection, supply voltage, output protocol, protection rating, and installation location at one time. Using “digital output required” as the sole condition cannot form an actionable technical specification.
For conventional industrial retrofit projects, 4-20mA can be used as the benchmark option with compatibility as the priority; for projects involving multi-point data acquisition, equipment networking, and remote parameter management, RS485/Modbus RTU can be evaluated first; for projects with existing DCS or industrial network standards, selection should be unified according to platform protocols, master station capabilities, and maintenance specifications.
Xi'an Shenghongchuang Instrumentation Co., Ltd. can provide selection support for differential pressure sensors and matching transmitters based on the on-site control system, measurement medium, and installation conditions. After submitting the existing PLC or DCS model, number of measuring points, range, transmission distance, and on-site operating conditions, suitable output protocols, wiring solutions, and communication parameters can be further confirmed to reduce subsequent commissioning risks.
Related Recommendations