News Center

——  NEWS CENTER  ——

News Center
Contact Us

Xi'an Shenghongchuang Instrument Co., Ltd.

Contact: Mr. Zhang

Mobile: 15529283736
Email: shc-sensor@qq.com

Address: Fortune Building, Sanqiao Street, Xixian New Area, Xi'an, Shaanxi Province

What Response Time Should a High-Speed Pressure Transmitter Achieve?
Added to Favorites:125

High-Speed Pressure Transmitter Response Time: First Clarify What “Fast” Means

The response time requirement for a high-speed pressure transmitter should not simply be understood as the smaller the value, the better. For machinery manufacturing, hydraulic control, test equipment, and high-speed production lines, the transmitter needs to reflect pressure changes promptly. However, under operating conditions involving pulsation, impact, or severe vibration, an excessively fast response may instead transmit transient disturbances in full to the control system, causing frequent valve actions, display fluctuations, or even control loop oscillation.

During engineering selection, it is necessary to distinguish among the response time of the sensor element itself, the transmitter's electronic processing time, the output signal refresh period, and the control system scan cycle. Some products specify a response time of less than 10 ms, which usually reflects the speed of the sensing element or internal conversion. If the PLC scan cycle is 20 ms and the analog module filter is set to 50 ms, the actual time for the system to obtain effective control data will still be longer.

Therefore, reasonable specifications for high-speed pressure transmitters should be determined based on the process cycle. For standard hydraulic equipment completing 2 to 5 actions per second, 10 ms to 50 ms can generally meet control requirements. For dynamic pressure testing, rapid stamping, or high-frequency pulse monitoring, confirmation should be made based on the pressure variation frequency, sampling system bandwidth, and data recording capability.

Differences Between Response Time, Rise Time, and Refresh Period

Response time generally refers to the time required for the output signal to reach a specified stable range after the input pressure undergoes a step change. Common evaluation criteria include reaching 63%, 90%, or 95% of the final value, and the standards used by different manufacturers are not entirely consistent. If purchasing decisions compare only the “ms” value without confirming test conditions, products with seemingly identical specifications may have significantly different actual dynamic performance.

Rise time focuses more on the time required for the output to change from 10% to 90%, and it can be used to assess the transmitter's ability to track rapidly changing signals. The refresh period is the interval at which a digital circuit or communication interface updates a measurement value. For example, if an RS485 output updates every 20 ms, externally read data will still be limited by this interval even if the sensing element itself responds faster.

For products with 4-20mA output, load, cable length, and downstream module filtering should also be considered. When shielded cables are generally used in industrial sites and the transmission distance is within 100m, signal transmission delay is usually not the main issue. The factors that truly affect system response are often transmitter damping settings, controller program cycles, and the actual action speed of the actuator.

Reference for Common Dynamic Specifications

Application ScenariosRecommended Response TimeSelection Considerations
Storage tank pressure, water supply pipeline network100ms to 500msStability, interference resistance, long-term drift
Hydraulic power units, injection molding equipment10ms to 50msPulsation adaptability, overload capacity, adjustable damping
High-speed test benches, impact testing1ms to 10msFrequency response bandwidth, synchronous sampling, peak capture

Factors Determining the Actual Performance of High-Speed Pressure Transmitters

The structure of the sensing element is the foundation of response performance. Pressure sensing elements based on different principles, such as diffused silicon, ceramic capacitance, and metal thin film, each have their own strengths in dynamic characteristics, pressure resistance, and media compatibility. For high-frequency pressure variation applications, in addition to the frequency response of the sensing element itself, pressure signal lag caused by excessively narrow pressure ports or overly long pressure guide chambers should also be avoided.

The condition of the medium must likewise not be overlooked. Liquid media transmit pressure relatively directly, whereas gaseous media are compressible, and long-distance pressure-sensing pipes cause more noticeable delay. High-viscosity liquids, particle-containing media, or media prone to crystallization may clog the pressure connection, extending response time from tens of milliseconds to several seconds or even causing measurement distortion.

Electronic damping is a parameter often overlooked in the field. A damping setting of 0.1s can suppress some pressure fluctuations; settings of 1s or 2s make the display and output more stable, but reduce rapid control capability accordingly. The appropriate approach is to first determine whether pressure fluctuations have process significance, and then decide whether to retain dynamic signals or apply filtering.

Matching Response Time and Damping Parameters to Control Objectives

If the pressure signal is used for a safety interlock, priority should be given to confirming the total delay from pressure change to alarm output by the controller, rather than focusing solely on transmitter specifications. For example, with a transmitter response of 10 ms, a PLC scan of 20 ms, logical processing of 10 ms, and relay and actuator action of 30 ms, the total response time is approximately 70 ms. The safety threshold and equipment inertia must be evaluated throughout this complete chain.

If the pressure signal is used for closed-loop regulation, the time constant of the process object must be considered. For air storage tanks and water supply systems that change slowly by nature, selecting a 1 ms-level product will generally not improve control performance, but may instead increase the budget and amplify field noise. For fast-action systems such as servo hydraulics and precision press fitting, the response capabilities of the transmitter, controller, and proportional valve should be on the same order of magnitude.

It is recommended to retain adjustable damping margin during commissioning. Start with 50 ms or 100 ms, observe pressure waveforms, actuator actions, and control errors based on the curves, and then gradually shorten or extend the filtering time. For operating conditions with frequent spikes, the issue should not be addressed solely by increasing damping; hydraulic shock, pump-source pulsation, installation vibration, and grounding and shielding issues should also be investigated.

Control ObjectiveRecommended Damping RangeSystem Configuration Recommendations
Trend monitoring and remote display0.5s to 2sBalances reading stability and communication refresh rate
General closed-loop pressure regulation50ms to 200msSet in conjunction with the PLC cycle and valve speed
High-speed dynamic control0ms to 20msVerify sampling frequency, vibration resistance, and peak protection

What Other Parameters Should Be Verified When Selecting a High-Speed Pressure Transmitter?

The measuring range should be selected so that normal operating pressure falls within 30% to 80% of full scale. An excessively large range reduces effective resolution, while an overly small range can easily exceed limits during startup, stall, or pressure shock. For systems that may experience pressure shocks of 1.5 to 2 times the rated pressure, overload pressure and burst pressure should be carefully verified rather than considering only the rated range.

Accuracy and response speed need to be balanced. High-accuracy models generally require stricter temperature compensation and calibration. Common accuracy classes include 0.5%FS, 0.25%FS, and 0.1%FS. If the actual allowable control error is 1%FS, blindly pursuing 0.1%FS may not be economical. However, in metering, testing, or highly consistent control applications, zero stability and temperature drift specifications are more valuable.

Xi'an Shenghongchuang Instrumentation Co., Ltd. and its subsidiary, Shaanxi Qinkong Sensor Technology Co., Ltd., can provide supporting selection services based on pressure range, medium temperature, connection type, output method, and dynamic requirements. For high-temperature, high-pressure, strong-interference, or non-standard installation applications, process flow, maximum pressure, medium composition, control cycle, and installation location should be provided before ordering to confirm suitable sensing elements, structures, and signal processing solutions.

Complete Final Confirmation with Field Data Before Purchase

Purchasing personnel should require suppliers to clearly define the response time test conditions, including step-pressure amplitude, medium type, output method, damping status, and evaluation percentage. Further defining “response time less than 10 ms” as “time required to reach 90% output” can effectively avoid performance misjudgments caused by different promotional definitions.

During technical evaluation, a sample unit can be arranged for verification in the actual piping system. Record pressure trends continuously for no less than 30 minutes while simultaneously reviewing PLC sampling values and actuator actions. Focus on whether there is zero drift, spike-induced false triggering, output delay, cable interference, and stability changes under high- and low-temperature conditions, rather than performing only static pressure calibration.

If it is necessary to determine high-speed pressure transmitter response time requirements, the pressure curves, control cycle, measuring range, medium, and installation connection of existing equipment can be compiled and submitted to Shenghongchuang technical personnel for operating-condition verification. After sample testing and parameter confirmation, determining the measuring range, accuracy, damping, output signal, and protection configuration will better align purchasing investment with actual control performance.

Submit