News Center

——  NEWS CENTER  ——

News Center
Contact Us

Xi'an Shenghongchuang Instrument Co., Ltd.

Contact: Mr. Zhang

Mobile: 15529283736
Email: shc-sensor@qq.com

Address: Fortune Building, Sanqiao Street, Xixian New Area, Xi'an, Shaanxi Province

Is the Shenghongchuang water level gauge suitable for small water tanks?
Added to Favorites:125

Is Shenghongchuang Water Level Meter Suitable for Small Water Tanks? Start with Actual Operating Conditions

Shenghongchuang water level meters can be used for liquid level monitoring in small water tanks, but whether they are "suitable" cannot be determined solely by tank volume. For applications such as equipment make-up water tanks, cooling water tanks, cleaning solution tanks, circulating water tanks, and fire protection make-up water tanks, the effective liquid depth, installation location, medium condition, output signal, and whether interlock control is required are more critical. Liquid levels in small tanks usually change rapidly. If the selected range is too large or the installation is improper, issues such as insufficient measurement resolution, inaccurate alarm points, or frequent start-stop operation may occur.

Xi'an Shenghongchuang Instruments & Meters Co., Ltd., supported by the manufacturing and testing capabilities of Shaanxi Qinkong Sensor Technology Co., Ltd., can provide supporting products including level transmitters, pressure transmitters, and intelligent digital display control instruments. For small water storage containers, submersible, hydrostatic, side-mounted, or level measurement solutions with display and control functions can be configured according to tank height, liquid type, port dimensions, and control requirements.

For example, if the effective liquid depth of a water tank is 500 mm, directly selecting a general-purpose product with a 0–10 m range is not recommended. Although an excessively large range can measure the liquid level, signal changes in the low-level range will be smaller, affecting the control system's accuracy in identifying the make-up water point and pump stop point. Generally, while preventing full-scale overload, the normal liquid level should fall within 30%–80% of the measuring range.

For small water tanks requiring only high- and low-level alarms, a level switch solution may be more direct. For systems requiring continuous level display, remote transmission to a PLC, or variable-frequency control of a make-up water pump, level transmitters with 4–20 mA, 0–10 V, or RS485 communication outputs are more suitable. Clearly defining whether the requirement is to "view the level" or "control the level" before selection can prevent insufficient functionality or unnecessary costs.

Four Key Conditions for Liquid Level Measurement in Small Water Tanks

The Measuring Range Must Match the Effective Liquid Depth

Measuring range is the first parameter for selecting a solution for a small water tank. The vertical distance from the tank bottom to the highest permissible liquid level should be measured, with an appropriate safety margin reserved. If the effective tank height is 800 mm, a 0–1 m range can be assessed first. If the maximum liquid level may rise temporarily due to surface fluctuations, the margin should be determined based on the overflow outlet, water inlet location, and fluctuation amplitude.

Hydrostatic level transmitters calculate liquid level based on liquid column pressure. Under clean-water conditions, approximately 10 m of water column corresponds to 0.1 MPa of pressure. Therefore, a water depth of 1 m corresponds to approximately 10 kPa. Although the pressure value is low within a small level range, stable measurement can still be achieved as long as the sensor range, accuracy class, and calibration method are properly matched.

When the tank height is below 300 mm, special attention should be paid to the sensor's low-range capability and control deadband. If the make-up water pump has a high flow rate per minute, the liquid level may pass through the alarm range within tens of seconds. In this case, not only measurement accuracy but also appropriate hysteresis settings in the PLC or control instrument should be considered to reduce the risk of frequent pump start-stop operation.

Shenghongchuang can provide corresponding range recommendations based on the actual liquid depth and ensure a clear relationship between output signal and measuring range through factory calibration. When purchasing, the tank height, minimum operating liquid level, maximum operating liquid level, and installation method should be provided rather than simply describing "a small water tank," so that an implementable measurement configuration can be developed.

Installation Space Determines the Sensor Structure

A common issue with small water tanks is not that sensors cannot measure them, but that small top openings and internal float valves, agitators, or inlet pipes result in limited installation space. Submersible level transmitters are usually inserted into the tank from the top and are suitable for structures with a top opening or existing access port. Side-mounted pressure solutions are suitable for containers with connections at the tank bottom or lower side.

When installing a submersible probe, it should be kept away from directly below the water inlet, near the pump suction inlet, and areas with strong agitation. Water impact can cause temporary fluctuations in liquid surface pressure, resulting in unstable displayed values. For small water tanks less than 1 m high, a distance of 30 mm–80 mm between the probe and the tank bottom is common, reducing the possibility of sediment covering the probe.

For side-mounted level transmitters, the location of the installation port requires attention. If the connection is located at the tank bottom, the measurement signal is stable, but the container may need to be drained for maintenance. If the connection is positioned too high, the low-level stage cannot be fully covered. For equipment requiring continuous water supply, a shut-off valve, bypass pipe, or maintenance connection can be added to facilitate subsequent maintenance.

Cable length should also be configured according to the on-site distance. Sensor cables should not remain under tension for extended periods, and wiring terminals should be kept away from damp or water-accumulation areas. If interference sources such as motors, variable-frequency drives, or solenoid valves are present on site, signal cables should be routed separately from power cables. Shielded cables and proper grounding should be used where necessary.

Selection Reference for Different Small Water Tank Applications

Application ScenarioRecommended Measurement MethodRecommended SignalKey Considerations
Equipment Automatic Water Replenishment TankSubmersible or Hydrostatic Level Transmitter4~20mALow-level start, high-level stop, and control hysteresis
Small Circulating Water TankInterference-resistant Submersible Level Transmitter4~20mA or RS485Water flow fluctuations, pump interference, and avoiding flow areas during installation
Cleaning Solution or Mildly Corrosive Liquid TankMedium-resistant Material Level Transmitter4~20mACorrosion resistance of the diaphragm, cable, and seals
Only Full and Low Water Level Alarms RequiredLevel Switch or Float SolutionSwitching SignalAlarm point location, contact capacity, and operating reliability

For ordinary tap water, purified water, or circulating cooling water, hydrostatic level transmitters are widely used and can continuously output the current liquid level value. If the system is already equipped with a PLC, a 4–20 mA signal is generally convenient for connection to an analog input module and offers interference resistance well suited to industrial sites. For long-distance or centralized multi-point monitoring applications, an RS485 communication solution can be further evaluated.

If the liquid in the tank contains foam, suspended solids, oil contamination, or corrosive components, selection cannot be based solely on clean-water conditions. Changes in liquid density affect hydrostatic conversion results, adherent materials may affect probe response, and corrosive liquids place higher requirements on stainless steel diaphragms, polyurethane cables, and sealing materials. The medium name, temperature, and concentration should be specified before ordering.

Small water tank level control should also match the operating rhythm of the equipment. For example, if a make-up water pump has a flow rate of 2 m³/h while the tank effective volume is only 100 L, one filling cycle can theoretically be completed in approximately 3 minutes. If the high- and low-level setpoint distance is too small in such systems, pump start frequency will increase significantly. Operating conditions can be improved by expanding the control level range or setting time-delay logic.

Shenghongchuang level transmitters can be used together with intelligent digital display control instruments to achieve on-site level display, upper and lower limit alarms, relay output, and linkage with make-up water equipment. For small equipment without a PLC, this combination can reduce control links and make it convenient for operators to read liquid levels and troubleshoot abnormalities on site.

How to Determine Accuracy, Output, and Control Method

Continuous Measurement Does Not Necessarily Mean Pursuing the Highest Accuracy

Selection for small water tanks should be based on actual control requirements. If the purpose is only to prevent dry running due to water shortage or avoid overflow, the focus of level measurement is stable identification of the alarm range. Higher accuracy and repeatability are needed only when quantitative liquid preparation, precise water addition, or closed-loop process level control is involved. Blindly increasing the accuracy class does not necessarily improve the control performance of the entire system.

Taking a 0–1 m range as an example, if the overall accuracy is 0.5%FS, the theoretical error is approximately 5 mm. If the range is expanded to 0–5 m, the theoretical error at the same 0.5%FS becomes approximately 25 mm. For small water tanks, proper range matching is often more important than emphasizing the accuracy class alone and is more conducive to obtaining usable liquid level change information.

A 4–20 mA output is suitable for most industrial control applications. 4 mA can correspond to zero liquid level or the lower range limit, while 20 mA corresponds to full scale. Line faults can generally be identified through abnormal current. A 0–10 V output can also be used for short-distance connections within equipment, but voltage drop and electromagnetic interference require greater attention for long-distance wiring.

If RS485 or another digital communication method is used, the protocol, baud rate, station address, and host computer compatibility should be confirmed. For projects requiring connection to existing automated production lines, it is recommended during procurement to verify the control cabinet's analog input range, power supply voltage, communication interface, and program conversion rules at the same time, avoiding issues where signals cannot be directly connected after product delivery.

Common Parameter Confirmation Table

Item to ConfirmSmall Water Tank Selection RecommendationsCommon Overlooked Risks
Measuring RangeSelect according to the effective liquid depth, leaving an appropriate marginExcessive range resulting in insufficient low-level resolution
Power Supply MethodTypically 24VDC; verify the on-site power supplyPower supply mismatch causing no output or abnormal signals
Output signalConfirm based on the PLC, instrument, or controller interface firstIncompatibility between analog and communication interfaces
Medium TemperatureSpecify the normal temperature, maximum temperature, and whether thermal shock is presentSeal aging, zero drift, or reduced service life
Installation InterfaceProvide opening dimensions, thread specifications, or flange requirementsUnable to install upon delivery or requiring secondary modification

Commonly Overlooked Issues During Installation and Use

Submersible level sensors typically require pressure equalization through a vented cable. The cable end must not be sealed in environments with standing water, oil contamination, or high humidity. If the vent end becomes damp or blocked, measurement deviation may occur. During installation, the junction box or vent end should be placed in a dry location, and the cable jacket, sealing connectors, and fixing points should be inspected regularly.

For tanks containing sediment, the probe should not rest directly on the tank bottom. After sand, scale, or metal debris accumulates, it may block protective holes or mechanically damage the diaphragm. A mounting bracket, guide tube, or protective cover may be used according to site conditions, but the protective structure must not completely enclose the liquid passage around the probe, as this may affect pressure transmission.

Zero and full-scale verification should be performed during commissioning. When the tank is emptied or reaches a known low liquid level, confirm the instrument display and output current. After the liquid level rises to a known height, verify whether the displayed value corresponds to the actual value. For 4–20 mA signals, the level conversions corresponding to 4 mA, 12 mA, and 20 mA can be checked in the control system to prevent incorrect engineering unit settings.

Routine maintenance does not require frequent removal of the sensor, but liquid level display trends should be checked in conjunction with the equipment maintenance cycle. If the liquid level remains fixed for a long time, fluctuations increase abnormally, readings are low after the tank is full, or a signal remains when the tank is empty, first check the power supply, wiring, vent end, probe contamination, and control system conversion parameters. Professional personnel can then determine whether recalibration or replacement is required.

Small Water Tank Selection Conclusions and Coordination Recommendations

Overall, Shenghongchuang water level meters are suitable for use in small water tanks, especially in industrial equipment supporting applications requiring continuous liquid level monitoring, make-up water linkage, low-water alarms, and remote signal transmission. The prerequisite is to select the range according to the actual effective liquid depth and determine a submersible or side-mounted installation solution based on the container structure, rather than directly applying a general configuration for large water tanks.

For small tanks containing clean water, provide the tank height, volume, medium temperature, installation port location, power supply conditions, and required output signal as a priority. If automatic water replenishment is required, the pump flow rate, start-stop logic, and control cabinet interface should also be specified. The clearer the complete parameters are, the better the level transmitter, digital display control instrument, and alarm configuration can match the site requirements.

For media such as oil, wastewater, chemical liquids, or foamy liquids, additional information should be provided on liquid density, corrosiveness, viscosity, impurities, and maximum temperature. Shenghongchuang can provide targeted configurations for material, range, accuracy, connection, cable length, and signal type, enabling products to meet stable measurement and control requirements under normal operating conditions and in complex industrial environments.

When preparing to purchase or upgrade a small water tank level monitoring system, on-site tank photos, dimension drawings, liquid level control requirements, and existing control cabinet interface information can be submitted to Shenghongchuang technical personnel. The technical team can confirm the applicable model, installation location, and wiring solution before product configuration and implementation.

Submit